Main board EDAC

A	OSC shunt
B	OSC series
C	OSC PD2000
D	OSC trigger
E	amp0 shunt
F	amp0 series
H	amp0 PD2000
J	amp0 trigger
K	amp1 shunt
L	amp1 series
M	amp1 PD2000
N	amp1 trigger
P	amp2 shunt
R	amp2 series
S	amp2 PD2000
T	amp2 trigger
U	qswitch trigger
V
W
X	Gate
Y	Gate shield
Z	Fire
AA	Fire shield
AB	Fire tip
AC	Fire ring
AD	interlock optocoupler
AE	interlock
AF
AH
AJ
AK
AL
AM	6V rail    - for relay and LED drivers
AN	poweron relay coil
AP	dump relay coil
AR	spare relay coil

1	GND for all the coax
2
3
4
5
6
7
8
9
10
11	panel mode F dump		yellow big bundle
12	panel mode E fire		green big bundle
13	panel mode D charge		red big bundle
14	panel mode C key switch		blue big bundle
15	panel mode B			red small bundle
16	panel mode A			blue small bundle
17	panel mode common		black big bundle
18	panel buttons common		black small bundle
19	LED interlock			green
20	LED ready ALL			yellow
21	LED ready osc			black
22	LED ready amp0			blue
23	LED ready amp1			red
24	LED ready amp2			NC
25	LED spare			NC
26	+15V		for Power LED via 820 ohm resistor    green
27	+3.3V		for LED drivers and via 180 ohm resistor for supply LED	    red
28	data qswitch TX
29	data console TX pin 2
30	data qswitch RX 
31	data console RX	pin 3
32	GND  pin 5 (both)			black for LEDs
33	8 VAC			transformer secondary
34	8 VAC			transformer secondary
35	18 VAC  from OSC	OSC X
36	18 VAC			OSC Y


Qswitch D9
1	8VAC
2	8VAC
3	trigger signal		controller U
4	trigger shield		controller 1
5	NC
6	data GND		controller 32
7	data			controller 29   (reversed?)
8	data			controller 31	(reversed?)
9	NC


OSC and AMP M.34 connectors
A	NC
B	hot2 main CB load
C	hot1 to main CB line		transformer primary
D	hot1 to main CB line
E	fuse load
F	interlock   tie to J
H	to both relays NO contact	controller AD (interlock opto)
J	interlock   tie to F
K	NC
L	hot2 main CB load
M	hot2 to main CB line		transformer primary
N	hot1 main CB load
P	fuse line
R	to dump relay communtator    idealy through dump switch NC 
S	power relay communtator		controller AE (interlock opto)
T	hot1 coolant CB load
U	hot2 coolant CB load
V	hot1 main CB load
W	hot2 to main CB line
X	18VAC hot		controller 35
Y	18VAC center		controller 36
Z	18VAC hot		NC
AA	frame GND
BB	NC
CC	frame GND
DD	NC
EE	trigger			controller D, J, N, T
FF	shunt			controller A, E, K, P
HH	series shield	
JJ	PD2000 shield
KK	trigger shield
LL	shunt shield
MM	series			controller B, F, L, R
NN	PD2000			controller C, H, M, S


RS-232: D9
pins 1,4,6 tied together
pins 7,8 tied together
2       RxData  (controller 29)           RS232 blue
3       TxData  (controller 31)           RS232 yellow
5       GND     (controller 32)           RS232 green



on amp, tie R to S
